SN74HCT74DRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 46MHz |
| Propagation Delay | 28 ns |
| Turn On Delay Time | 18 ns |
| Family | HCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 25ns @ 5.5V, 50pF |
| Screening Level | MIL-PRF-38535 |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.58mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT74DRG4 Overview
In the form of 14-SOIC (0.154, 3.90mm Width), it has been packaged. It is contained within the Tape & Reel (TR)package. Differentialis the output configured for it. Positive Edgeis the trigger it is configured with. There is an electronic component mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. The operating temperature is -40°C~85°C TA. D-Typeis the type of this D latch. In this case, it is a type of FPGA belonging to the 74HCT series. You should not exceed 46MHzin the output frequency of the device. There is 4μA quiescent consumption. 14terminations have occurred. It is a member of the 74HCT74 family. The D flip flop is powered by a voltage of 5V . Its input capacitance is 3pF farads. It is a member of the HCTfamily of D flip flop. The electronic part is mounted in the way of Surface Mount. It is designed with 14 pins. The clock edge trigger type for this device is Positive Edge. It is included in FF/Latches. 2 circuits are used to achieve its superior flexibility. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. The system runs on a power supply of 5V watts. The supply voltage should be maintained at 5V for high efficiency. A total of 4input lines have been provided.
SN74HCT74DRG4 Features
Tape & Reel (TR) package
74HCT series
14 pins
5V power supplies
SN74HCT74DRG4 Applications
There are a lot of Texas Instruments SN74HCT74DRG4 Flip Flops applications.
- Counters
- ESD protection
- Bus hold
- ATE
- Circuit Design
- Single Down Count-Control Line
- Shift Registers
- Data storage
- Latch
- Cold spare funcion