SN74ACT574PWG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 110MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Number of Bits | 8 |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 7 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74ACT574PWG4 Overview
TSSOPis the way it is packaged. There have been 20 terminations. Power is supplied from a voltage of 5V volts. In this case, the D flip flop belongs to the ACTfamily. The electronic part is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. There are 8bits in its design. The superior flexibility of this circuit is achieved by using 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TUBE. It operates from 5V power supplies. This flip flop has a total of 2ports. The supply voltage should be maintained at 5V for high efficiency. There are 1 output lines on it. The number of input lines is 3. -24mA is set as the high level output current. There is no low level output current set at 24mA. The operating temperature should be lower than 85°C. It is recommended that the operating temperature be greater than -40°C. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis the maximum supply voltage it supports. We are able to achieve a frequency of 110MHz. It uses BUS DRIVERas its logic IC. A total of 1 functions are available on the T flip flop. 20pins are provided on the D latch. As a result of its output current of 24mA, it is very flexible in terms of design.
SN74ACT574PWG4 Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74ACT574PWG4 Applications
There are a lot of Texas Instruments SN74ACT574PWG4 Flip Flops applications.
- QML qualified product
- Functionally equivalent to the MC10/100EL29
- Divide a clock signal by 2 or 4
- Event Detectors
- Clock pulse
- ATE
- Computers
- Cold spare funcion
- Frequency Dividers
- Storage Registers